User Tools

Site Tools


logs

How to get logs and systemspecs:

In the majority of cases, simply describing your issue will not provide enough information for someone to identify it’s cause and advise you on how to resolve it. It is important to include any system logs that may be relevant to your issue to ensure that neither your time nor the other person’s time is wasted. The following is a list of the most common system logs and where/how to obtain them. The logs are listed in the order of importance.

Systemd Journal

The systemd journal can only be accessed using the journalctl command.

You can export your system’s journal from the last three boots using these commands:

su

journalctl -b -0> /tmp/journal

journalctl -b -1> /tmp/journal.last

journalctl -b -2> /tmp/journal.2last

exit

XSESSION

Your session log is located in your /home directory:

~/.xsession-errors

~/.xsession-errors.old

XORG (X11)

You can find your Xorg logs here:

/var/log/Xorg.0.log

/var/log/Xorg.0.log.old

LIGHTDM

LightDM’s logs can be found here:

/var/log/lightdm/lightdm.log

/var/log/lightdm/x-0-greeter.log

OTHER LOG PROVIDERS

journalctl –since “10 minutes ago”

To get journal from timespan (works also with hours seconds, days)

For problems after new installation:

cnchi logs under: /var/log/cnchi now: (before they was saved under /tmp)

/var/log/cnchi/cnchi-XXXXXXXX-XXXXXX.log

/var/log/cnchi/install_id

/var/log/cnchi/pacman-XXXXXXXX-XXXXXX.log

/var/log/cnchi/postinstall-XXXXXXXX-XXXXXX.log

To create an archive of all install logs:

tar -czf ~/cnchi-logs.tar.gz /var/log/cnchi/

Will create a cnchi-logs.tar.gz under the home of current user.

A good way to get information about a particular program:

journalctl -f /usr/bin/“Executable”

And nice to poste a pastebin the smart way:

“command” | curl -F c=@- https://ptpb.pw/?u=1

System summery and bootlog example:

systemsumup
lspci> log.txt && lsusb>> log.txt && journalctl -b -0>> log.txt && cat log.txt | curl -F c=@- https://ptpb.pw/?u=1

pastebinit

install pastebinit with package manager or sudo pacman -S pastebinit

command should be passed like this:

journalctl -b -0 > ~/journal.txt && pastebinit -i ~/journal.txt -b lpaste.net

where you can change journalctl -b -0 with any other command like dmesg from below, his will write to a txt file: ~/journal.txt under your home you can change this name (journal) to something related to the command you pass..

pastebinit will autoupload this to the pastebin service you can choose (list all aviable by pastebinit -l)

then it gives the link to it as output, so that you can just copy t to paste inside a post.

System summary example:

lspci > log.txt && lsusb » log.txt && dmesg » log.txt && pastebinit -i log.txt -b lpaste.net

This will give out a link (like this:http://lpaste.net/7802695579456241664) you can post onto the forum, this will include all the output of:

lspci (list your pci devices) lsusb (same for usb) and dmesg (bootup messages) and make it aviable.

The dmesg command:

An alternative to the above command (or if your system is not using systemd) is the good old dmesg//command. This is potentially less informative than journalctl above, but not if you have filtered it as I advised you to. So they are essentially equivalent.

dmesg

Again, If you look in its man page or type invoke dmesg –help you’ll learn about the always useful -l flag, which filters dmesg potentially long output to print only certain message levels. And the -r flag which prints the message level. So, likewise many of us will thank you if you do the following instead of the above:

dmesg -rl warn,err,crit

Or at the very least:

dmesg -r

Trivia: The dmesg command is basically the same as journalctl with the -k flag added to it

Hardware Information Systems:

INXI: smxi.org

inxi -Fxxc0

Or to autopastebin it and get an url to post:

inxi -Fxxc0 | curl -F c=@- https://ptpb.pw/?u=1

logs.txt · Last modified: 2018/03/11 22:22 by joekamprad